Payment & Shipping Terms:
|Type:||Water Tank Fire Truck,foam,dry Powder Fire Truck,rescue Fire Truck||Fire Pump:||Chinese Brand|
|Fire Monitor Range:||≥50M||Flow Rate Of Monitor:||48L/s|
|Flow Rate Of Pump:||60L/s||Steering:||LHD Or RHD|
fire service truck,
foam fire truck
ISUZU 3.5ton 4t water tank fire brigade truck 4000liters water fire fighting truck
1. water tank fire brigade truck is composed with truck body and cabin,cabin is two rows,which can allow 6 persons.The front part of truck body is equipment room,middle is water tank and foam tank,rear is pump room.
2) To ensure good performance of fire trucks,water tank fire brigade truck is equipped with middle and low pressure fire pump CB20.10/30.6o with flow rate at 60L/S and Chengdu Wester fire monitor PL48(PM160)or PS60W(SG160).
3) water tank fire brigade truck are widely used in factory,terminal,oil&gas depot to insure emergency fire cases.
Spec. of water tank fire brigade truck
|Fire pump rated flow||30Lemail@example.comMpa||Vacuum pump|
|water monitor rated flow||30-50Lfirstname.lastname@example.orgMPa|
|Water monitor range||Water range≥55m|
|1||Water tank capacity||water||3000kg||Built-in type|
|2||Fire pump model||CB20.10/15.30||Shanghai rongshen|
|3||Fire pump performance||30Lemail@example.comMpa;15L/S@2.0Mpa||Use vacuum pump to priming water|
|4||the installation site of fire pump||rear|
|5||The quantity of fire pump water outlet||4|
|6||Pressure gauge||0-2.5 Mpa||2.6 level|
|7||Vacuum gauge||-0.1- -1 MPa||2.6 level|
|Turning angle 360°|
|9||PTO Model||YTQ250 (MOTOR)|
The Overall layout
|The overall layout||
The front and two sides of the middle of the body are storage compartments. It is built-in type
independent water tank in the middle position of the central compartment. The back of the body
is pump compartment.
The aluminum alloy shutters are installed at both sides of the body and the back of the pump compartment,
the ladders are installed on the back of the body at the right side.
All welding panels and skeleton steels are through strict process of anti-rust, anti-corrosion and phosphating
pickling. All the accessories,standard components are processed of galvanization,electroplate,Dacromet
treatments and so on. After completing welding of the tank, the tank will be clear up and removed possible
defects such as empty solder. And then it will be through 24-hour hydrostatic test to assure no leakage.
The frame body
The outer frame of the body are all high quality Q235A, the inner frame use high strength aluminum alloy,
the bottom panel adopt aluminum panels with anodic oxidation treatment.
The doors are aluminum alloy structure with locks which are good sealing and dustproof.
|structure||Built-in tank, all metal welding structure, the overall corrosion resistance, have shock absorption measures|
High quality carbon steel Q235A,3-5mm(bottom thickness 5mm,side thickness 4mm,
top thickness 3mm)
|Structure||1 DN 470mm inlet hole|
|1 suction hole at the rear of pump room|
|1 overflow valve device|
|1 drain outlet with ball valve|
|2 DN65 inlets at both sides, structure:ball valve with inside bend upturning pipeline|
Fire control system
|Consist of fire pump,fire monitor,pipeline system,system operation panel|
|Model No||CB20.10/15.30 fire pump||
CB20.10/15.30 fire pump
|Type||Medium/low pressure Centrifugal pump|
|Outlet pressure||≤2.0 MPa|
|Maximum pumping height||7m|
|Priming device||Vacuum pump|
|Model No||PS30-50D fire monitor||
PS30-50D fire monitor
|Manufacturer||Zhangqiu fire equipment co., LTD|
|Rated flow||30-50L/S adjustable straight stream/spray/mist spray|
1 DN100 suction hole at the rear of the pump room with filter screen and pneumatic
Butterfly valve switch
|Injection pipeline||2 DN65 injection holes on both sides, 1 DN65 injection hole inside pump room.|
|Injecting water to tank||injecting water from pump to water tank through 1 Φ65mm injection hole inside pump room|
|Outlet pipeline||Two DN80 normal pressure outlets at the rear|
|Cooling pipelune||Cooling pipeline,control valve to cooling PTO|
|Heat device||To raise temperature in pump room(optional)|
|Cover||All inlet and outlet holes with covers|
|Display and control||
Marks on all operation buttons,with pipeline layout and operation/maintenance illustration.
Dashboard lays upper-left in the pump room with RPM/Vacuum/water pressure/liquid level
indicator and lighting/valves control switches
|PRM control of pump||
1.control in the drive cabin
2.remote manual control in the pump room
|Additional electrical||Independent circuit|
Headlamps are installed in the pump compartment and storage compartment. operating dashboard
is equipped with lighting switch, indicator light.etc. It is convenient for observation.
|Side flashing light||A set of red and blue flashing lights are installed on both sides of the vehicle body.|
|The warning device of the cabin||
Long red light 1 piece, which is installed on the top of the cabin;
Electronic alarm 1 piece, which is installed in the cabin;
The control box is installed below in front of the driver
|The fire lighting||
The fire lighting 1 piece
24V,60W remote omni-directional rotation fire lighting
|The main power||The vehicle battery is installed battery main switch.|
Working Scene of water tank fire brigade truck
Quick feedback to solve your questions
Professional engineering and production team
Related Accessories and spare parts offered,no future worries
Regular customer after-sale visiting
Free technical staff training and guidance
Reasonable price and good quality
Quick delivery and shipment
Q1: What kinds of water tank fire brigade truck I can order from your company?
A: There are various sizes and types of water tank fire brigade trucks with different functions,you can contact us and tell your request.We will recommend you suitable product.
Q2:: Have you supplied water tank fire brigade truck to any overseas companies?
A: Yes,with need of government project,we offered water tank fire brigade trucks to many Africa and south-east Asian,south-American countries.
Q3 What about warranty?
A: Equipment warranty is 12 months from the date on which the equipment is applied successfully into operation, or 13 months from the date on which the equipment has been delivered, whichever comes first.
Q5: Where is your factory? How far from Shanghai to your factory?
A: Our factory is based in Suizhou city, Hubei province, China. Our overseas marketing office is in Wuhan city,Hubei Province.Wuhan is about two hours' plane and four hours' high speed train from Beijing,Shanghai or Guangzhou city,welcome to visit us for factory inspection.
Contact Person: Ms. Shirley